_ _ _ _ _ _ _  
_
   
_
  _ _
 
 

Filling joints machine, plastering machine and injection pump FC 50

 
filling joints machine, small plastering machine, injection pump FC 50
 

DESCRIPTION

 

Filling joints machine FC 50 is a small single-phase horizontal worm pump with electronic range variation of pump output capacity by inverter with wired 24 V remote control from 0,5 to 12 l/min.
The pump FC 50 is unique in its class for versatility and ductility; with its large series of modulated optional accessories and kits that are very easy to install, FC 50 pump con be transform from a filling joints machine to an injection / grouting pump or into a small plastering machine for traditional, ready-mix, special finish plasters that it must be mixed separately with a water by a mixer. In particular, with the FC 50 pump you can perform filling the joints at least with a width of 8 mm on brick, brick facades, porphyry, paving, different types of stones and pebbles of various sizes with traditional mortars, ready-mix mortars, additives-expansive, anti-retirement, and also you can do consolidations and anchorage.
FC 50 machine, with its optional accessories and kits you can perform grouting and controlled pressure injection of cement, expansive mortar, thixotropic mortar, resins and other mortar injection in the wall cables channels and in the pre-compressed structures; also it can be used as plastering machine to spray wet mortars, traditional and ready-mix mortars based lime, cement or gypsum, finish mortars and special thermal insulating plaster.
Furthermore with portable screw compressor with min. output of 500 l/min, it can be spray special wet mortars, water proofing, acoustics, fire proofing, fire protection, insulating, protective coatings and leveling coatings.
Other peculiarities are the simplicity, the reduced maintenance, and the small size that make it very handy.
On web page FC 50 in a building site, you can view a photo report about execution of controlled pressure injection and filling of joints between the stones that composed the walls along flight of steps of Carmini near the prestigious "piazza degli Scacchi" , Marostica (VI) - ITALY, with filling joints machine FC 50.

 

FEATURES

 
  • Machine is very handy and compact.
  • Even in a configuration of 2.2 kW small plastering machine, the power consumption is low, and it can be connected to the civil building with power source of 3 kW - 230 V single phase, ensuring excellent performance.
  • The wired 24 V remote control during filling joints allows the machine to operate continuously or intermittently (useful for finishing) and unique in its category, it can be adjust the pump output capacity directly on the same command.
  • All accessories are modular and easy to install even by the operator, without the intervention of technicians and it's possible to purchase and install this kits in a later time and not only when you make the purchase order of the machine.
  • Very quiet at work.
  • Maintenance and cleaning are very fast.
 

TECHNICAL DATA

 
FC 50 - 1,5 kW FC 50 - 2,2 kW
Voltage 230 V single-phase 230 V single-phase
Pump motor 1,5 kW 2,2 kW
Maximum aggregate size up to 4 mm up to 7 mm
Pump output capacity adjustable from 0,5 to 9 l/min
(optional up to 12 l/min) by inverter
adjust from 0,5 to 12 l/min
(optional up to 20 l/min) by inverter
Hopper capacity 50 l 50 l
Length x width x height 1200 x 700 x 500 mm 1200 x 700 x 500 mm
Total weight 85 kg 90 kg
Standard hose equipment 10 m - single piece 10 m - single piece
Other material in a standard equipment Instructions manual, 2 filling guns, wired 24 V remote control, toolbox, accessories and declaration of conformity. Instructions manual, 2 filling guns, wired 24 V remote control, toolbox, accessories and declaration of conformity.
 

OPTIONAL KITS AND ACCESSORIES

 
Plastering machine configuration. FC 50 - 1,5 kW FC 50 - 2,2 kW

Small plastering machine for traditional wet mortar up 5 mm.
(suggest R 50 M planetary mixer)

NOT applicable. It needs air compressor kit, plastering mortar hose, vibrating screen and spray gun.
Small plastering machine for ready-mix mortar up 5 mm.
(suggest IMPACT continuous mixer)
NOT applicable. It needs air compressor kit, plastering mortar hose and spray gun.
Plastering machine for finishing wet plaster up to 3 mm.
(suggest R 50 M planetary mixer)
It needs air compressor kit and spray gun.
(optional inner agitator)
It needs air compressor kit and spray gun.
(optional inner agitator)

Injection pump configuration.

   
Controlled pressure injection and grouting
(suggest R 50 M planetary mixer)
Manual or automatic injection kit or manual with recycle. Manual or automatic injection kit or manual with recycle.

Other options (on request).

   
For difficult amalgamation mortars. Inner agitator. Inner agitator.
 

DETAILED PICS

 
Filling gun and wired 24 V remote control of filling joints machine FC 50 air compressor kit for small plastering machine FC 50

Filling gun and wired 24 V remote control.

Air compressor kit.

 
injection gun kit for controlled pressure injection of cement of pump FC 50 single-phase small plastering machine for traditional mortar FC 50.

Injection gun kit.

Example of plastering machine mode.

 
Vibrating screen for traditional mortars of small plaster sprayer FC 50

Vibrating screen for traditional mortars.

 

top page